一本久道竹内纱里奈中文字幕_91精品91久久久中77777_黄色在线视频网址_成人一区精品_少妇精品蜜桃偷拍高潮系列_国产激情一区

Welcome to visiting our website

| ||Contact

Dongguan Jieyu Machinery Co., Ltd

  • Dongguan Jieyu Machinery Co., Ltd. [national high tech enterprise]
  • Production of super wear and corrosion resistant screw

    Hotline138-2699-5065139-2580-9520

    Contact
    contact number:

    13826995065 (Mr. Deng)

    13925809520 (Miss Zhou)

    Tel: 0769-81885355

    Fax: 0769-81885356

    Address: No.313, Zhenan West Road, Shangjiao, Chang'an Town, Dongguan City, Guangdong Province
    Location:Home > News and information > Industry information > 

    Selection and disassembly of screw of injection molding machine

    Pubdate:2020-02-10 13:39:50
    How to decide the screw of injection molding machine

    In order to avoid material storage, there is no check ring, and the head taper is 20 ° - 30 °. It is more suitable for soft glue. If the product demands higher requirements, the non metering section and separated screw can be used. This screw is more suitable for hard PVC. In addition, in order to cooperate with temperature control, cooling water or oil holes are added inside the screw in the feeding section, cold water or oil tank are added to the cylinder, and the temperature control accuracy is close to 2 ℃.

    How to decide the screw of injection molding machine: parameters

    L / D refers to the length diameter ratio of the screw, l is the effective length of the threaded part of the rod. Under the condition of a certain diameter, the larger the length diameter ratio is, the longer the thread length is, which directly affects the thermal process of the material in the rod and the ability of connecting pipe energy; if the L / D is too small, it directly affects the melting effect and melt character of the material; if the L / D is too large, the transmission torque increases and the energy consumption increases.

    L1 refers to the length of the feeding section and L1 should guarantee that there is sufficient conveying space for the materials, because too short L1 will lead to premature melting of the materials, so it is difficult to guarantee the conveying conditions of firm pressure, and it is also difficult to guarantee the plasticizing character and plasticizing ability of the screw in the following sections.

    H1 refers to the depth of screw groove in the feeding section. If the depth of H1 is deep, it will contain more materials, improve the feeding capacity and plasticizing capacity, but it will affect the plasticizing effect of materials and the shear strength of the screw root. Similarly, it is common H1 ≈ (0.12-0.16) d

    L3 refers to the length of melting section. The length of L3 is conducive to the fluctuation of melt in the screw groove, with firm pressure impregnation, so that the material is repelled from the screw head with a uniform amount of material, similarly ordinary L3 = (4-5)

    How to decide the screw barrel of injection molding machine: PMMA (plexiglass material)

    A. L / D selects the mutation type with the length diameter ratio of 20-22, depending on the accuracy of the product forming, it demands the same ordinary Li = 400%, L2 = 40%.

    B. Compression ratio: 2.3-2.6.

    C. In view of its hydrophilicity, the front end of the product adopts the mixing ring structure.

    D. The other parameters are also ordinary, which can be planned according to the process screw, and the gap between them is too large.

    How to dismantle the screw of injection molding machine

    The appearance of the screw used in the injection molding machine and the extruder is very similar. They are all cylindrical thin and long threaded rods with thread grooves. According to the thread type, there are two types: the mutation type of equal distance and unequal depth and the mutation type of thread depth changing from deep to shallow. Special tools shall be used for screw device of injection molding machine, and heavy hammer shall not be used for knocking. The specific device steps are as follows.

    ① Device nozzle and connection between nozzle and barrel.

    ② Separate the rear key connection from the drive shaft.

    ③ Connect the flange of the device and move the screw forward.

    ④ When the head is exposed from the barrel, immediately install the connecting thread (steady: the thread here is also ordinary, mostly left-handed).

    ⑤ Check ring and sealing ring on the screw rod of the device.

    ⑥ The nozzle, check ring and sealing ring on the device shall be cleaned immediately with copper brush and shovel tools when they are hot. In addition, the cat material that is difficult to clean shall be heated in the oven at the lowest temperature that can soften the material, and then the residual material shall be eliminated.

    ⑦ Assemble all parts together, and apply molybdenum disulfide heat-resistant grease to all threaded connection parts, so as to facilitate the next device.

    ⑧ After cleaning the outside of the temporarily inconvenient photographing rod, it shall be coated with protective oil, wrapped and hung at the safety place in the side view.

    Ordering hotline of screw products: 0769-81885355 13826995065 (Mr. Deng)
    13925809520 (Miss Zhou) 【粤ICP备2021093017号
    E-mail: jieyu@dgjieyu.com technical support [Dongguan website construction]
    Address: No.313, Zhenan West Road, Shangjiao, Chang'an Town, Dongguan City, Guangdong Province
    Copyright @ Dongguan Jieyu Machinery Co., Ltd






    WechatWechat

    主站蜘蛛池模板: 国产成人免费无码视频在线观看 | 草草青 | 日本www在线 | 男人的天堂中文字幕 | 日本一区二区高清 | 成人午夜国产福到在线不卡 | 小蜜被两老头吸奶头在线观看 | 亚洲精品韩国美女在线 | 亚州春色| 成人9久久国产精品品 | 91日韩视频在线观看 | 国产成人综合亚洲怡春院 | 午夜影视污 | 色噜噜狠狠成人中文小说 | 色五月丁香六月欧美综合 | 亚洲一区二区三区免费在线观看 | 乱成熟女人在线视频 | 国产成人精品曰本亚洲77美色 | 国产精品密蕾丝视频 | 亚洲 欧美 动漫 少妇 自拍 | 67194免费毛片入口在线看 | 久久2| 四虎最新地址 | 国产成人精品综合在线 | 67194熟妇人妻欧美日韩 | 天天色天 | 插吧插吧综合网 | 久久久久无码精品国产app | 毛片2016免费视频 | 在线精品国精品国产不卡 | 久久精品国产精品亚洲20 | 欧美男女激情视频 | 亚洲精品手机在线 | 在线黄视频网站 | 成人中文字幕一区二区三区 | 48久久国产精品性色aⅴ人妻 | 高清不卡一区二区三区 | www男人的天堂 | 一国产一级淫片a免费播放口 | 久久中文字幕一区二区 | 国内外精品影视大全 |